Lesson 07 / Correction

EQ Target Matching & Speaker/Sub Alignment

The two jobs that actually improve in-room response: aligning sources so they sum, then EQing what remains — with discipline.

Purpose

REW's EQ window models filters and predicts results including non-minimum-phase effects. The Alignment Tool predicts summed response of two measurements with gain/delay/polarity. Together they solve integration before correction.

Workflow A — Target Matching (EQ Window)

  1. Open EQ: Select equaliser model (Generic, miniDSP, CamillaDSP, etc.). Note sample rate in panel title — biquad coefficients are rate-specific. Q definitions vary by model.
  2. Target Settings: Choose type: Full Range / Bass Limited / Subwoofer / Speaker Driver. Set LF cutoff + slope, bass management cutoff/slope, crossover filters.
  3. House/Room Curve: Add room curve (LF rise start/end/slope + HF fall start/slope) OR load house curve file:
    20 6.0
    80 0.0
    200 0.0
    20000 -2.0
    Format: freq offset pairs. This tilts the target — subjective preference, not correction.
  4. Target Level: Auto or manual. This is the level REW matches to — not a volume control. Set match range (e.g. 20–200Hz for modal EQ).
  5. Match Parameters: Max boost (set 0 for pro work — cut only), flatness target, allow narrow filters below 200Hz (yes for modal), allow shelves.
  6. Match Response to Target: Press match. Inspect Filter Adjust graph: measured, predicted, target, filters, filters+target. Check predicted waterfall/phase/group delay — not just SPL.
  7. Optimize: Adjust gains/Qs/frequencies. Watch headroom — cuts reduce level, boosts eat headroom. REW won't auto-boost below natural roll-off unless allowed.
  8. Deploy: Send to equaliser via Filter Tasks, or Save filter coefficients (biquads for miniDSP/SigmaStudio), or Measure with these filters (acoustic verification without hardware).

Workflow B — Sub/Main Alignment

  1. Measure with timing reference: Loopback or acoustic timing reference required — otherwise phase/delay comparisons are meaningless. Measure main alone, sub alone, both together.
  2. All SPL → Alignment Tool: Select main + sub. Choose Phase alignment (aligns phase slopes / phase at cursor) or Impulse alignment (cross-correlates 1/3-octave filtered IRs).
  3. Adjust: Set cursor near crossover (e.g. 80Hz). Adjust delay, gain, polarity of sub. Use Aligned sum to preview combined response. Look for smooth crossover (no cancellation dip) and aligned phase traces.
  4. Verify: Check excess group delay flattens after alignment. Apply delay/polarity in AV processor, re-measure both together.

Worked Example — Fix 50Hz Mode + Align Sub at 80Hz

  1. Mic at MLP, 48kHz, timing reference loopback. Measure sub alone (10–300Hz, 512k sweep, -12dBFS, 75dB SPL).
  2. SPL shows +11dB at 51Hz, waterfall ridge at 51Hz. Modal Analysis finds resonance 51.2Hz, T60 0.9s.
  3. EQ → Subwoofer target, LF cutoff 25Hz, match range 20–200Hz, max boost 0, narrow filters allowed. Match → proposes -9dB Q=8 at 51Hz (modal filter matched to T60). Predicted waterfall shows ridge shortened. Headroom -2dB.
  4. Measure main + sub with timing ref. Alignment Tool: phase mode, cursor 80Hz, sub delay +4.2ms, polarity invert. Aligned sum shows +3dB summation, no dip. Excess GD flat through crossover.
  5. Send filters to miniDSP, set AVR sub distance +1.45m (4.2ms × 343m/s), re-measure — confirm.

Outputs & Interpretation

  • Filter Adjust: Predicted trace is what REW thinks you'll get — includes non-minimum-phase limits. If predicted still shows dip, that's uncorrectable.
  • Pole-Zero plot: Poles = resonances, zeros = filter notches. Useful for modal filter sanity check.
  • Aligned sum: Predicted acoustic sum. If it shows cancellation, fix delay/polarity first — never EQ a crossover dip.
  • Trace Arithmetic: A/B, A+B, merge (auto-aligns mag+phase at merge freq), invert. All depend on window settings — keep them consistent.
Deeper Detail — Filter Types, Averaging & House Curves

Filter types: PK (peaking), LS/HS (shelving), LP/HP, notch, all-pass. Modal filters adjust Q to match target T60 — useful for ringing modes.

Boost Q limits: Prevent narrow boosts that create artificial resonances. Keep max boost low or zero.

Averaging: RMS (incoherent, power average), dB average, Vector (coherent, uses phase — requires time/level alignment), RMS+phase, dB+phase. Vector average without alignment is meaningless.

House curve philosophy: Bass boost (+6dB at 20Hz → 0dB at 80Hz) and HF fall are preference. Too much bass boost excites modes and wastes headroom. Check multiple positions before finalizing — EQ is only valid at measurement position (LF more stable, HF varies rapidly).

Equaliser models: Generic/Extended support many types. Specific models (Dutch & Dutch 8c, Hypex, StormAudio) have network transfer. BFD DSP1124P needs Store Enable. FBQ2496 transfer can be unreliable — adjust filter delay.

Check Your Understanding

Combined sub+main shows deep narrow dip at 85Hz (crossover 80Hz). Individual responses look fine. First move?